Wednesday, May 15, 2013

All Cord or All Rod Mechanics?

Sometimes beginning figure makers get all hung up on thinking they have to do all rod control mechanics. They see some of the figure makers out there that do this style of mechanics and get it in their head that it is the only way to go, or the best way to go. They think they can not build a really high quality figure without going that route.  Is that true? Read on.......

First of all, doing all rod control mechanics (also called direct linkage), is an advanced technique and takes quite a bit of know how and skill to accomplish. To make direct linkage mechanics quiet and reliable is quite the challenge. I know because I have done them several times over the years I've been making figures. Here's an example of a figure I've done that way............



It turned out very nice and the customer really liked the way they functioned and how quiet they were, but I can tell you it is a lot of painstaking work to accomplish. By comparison, all cord mechanics are a piece of cake! Here's an all cord mechanics figure that I did recently............


It functions very nicely as well. Here is a shot of the inside of that figure, to show how simple the mechanics can be.............


Adding additional mechanics inside the head is easier with all cord control typically. Here a is a shot of the inside of another figure that had raising eyebrows added..........


All cord mechanics are easier to make and typically much easier to make them operate quietly compared to all rod control mechanics. The figure builder pulls a lot less of his or her hair out! (grin) So is all cord mechanics better in some way than all rod mechanics? Or is all rod mechanics better than all cord mechanics?

If done well, either all cord or direct linkage can be good. If done poorly, either one can be a nightmare! Each has its advantages and disadvantages. If cord control is done poorly, the cords can fray and even break prematurely. But if done well, they can last a long time, rarely break, and operate nice and quiet. But if a cord did break at some point, the owner could most likely fix it himself, or if he sent it out to be fixed, it usually would be an inexpensive repair, which is nice.

But again, if done well the cords rarely break. Here a Chuck Jackson all cord control head stick.............


I put all new brass levers on this head stick. But I did not have to replace the cords. They were still in great shape and there was no need to replace them.

If done poorly, all rod control can end up being quite noisy and need repair soon. And if something does go wrong, it is very doubtful that the average figure owner could repair it himself. It's just too complicated. And if you have to send it out to be repaired, it could potentially be very pricey to fix. Also, you could not send it to just any figure maker to fix it. If done well however, all rod control can be very responsive, and be a delight to operate.

Many top figure makers (Guyll, Semok, Hartz, Marshall, etc.) have made some great figures with all cord control (some may do rod control eyes, but all else is cord control) that have held up very well over time. And the same can be said of some top figure makers that have used all rod control. In both cases, the figure mechanics have been crafted very well.

It would be much better to make an all cord control figure that functioned well, than to make an all rod control figure where the mechanics were very noisy, and the mechanical connections were binding/squeaking, etc.

So which is better? All rod control or all cord control? In my humble opinion, both methods are very viable ways of mechanizing and animating a professional ventriloquist figure, if..........., done well.

In the end, it can get down to personal preference as to what building style you would like to go for. My recommendation for beginning figure makers (or kit builders), is to start primarily with cord control mechanics on your first figure or two.

Then, as you get more familiar with figure building, think about experimenting with some rod control mechanics. Maybe just one or two rod control animations. The eye mechanism is the easiest rod control mechanics to learn. The mouth is the next easiest perhaps. Winkers and eyebrows can be a bit more involved.

Also, remember, a figure does not have to be all cord control or all rod control. It can be a combination of both. Over time, you will find what works best for you and your building style.


Saturday, May 4, 2013

Cast Ventriloquist Dummy Parts.....



  In December of 2012 we had to temporarily halt production of our high quality cast dummy parts. We needed some time to catch up a bit here with our finished figure orders. Since that time we of course have had numerous people contacting us to see when they would be available again. We've made some arrangements here, and that time is NOW! Click on link below.......

Cast Dummy Parts




  You may need to refresh your browser for those pages to show properly. Our cast parts have been helping people build figures since 1993! It has been very gratifying helping so many get started making their own figures. In fact some have gone on to making and selling figures themselves and have done quite well. Some names that might surprise you. I'm just happy to have had a part behind the scenes here.

  There have been numerous phone calls, emails, etc., over these years of providing cast parts and instruction on building figures. On occasion that can get to be a bit overwhelming, but all in all, I really do enjoy teaching others as I have the time to do so. Always have enjoyed that part of it.

p.s. my wife Cathy is doing a lot better now. Thanks to all who inquired about her!